Rohnson R-031 Glass Convection Heater with Wi-Fi Instruction Manual Product Information (2024)

R-031 Glass Convection Heater with Wi-Fi

Specifications

• Model No.: R-031
• Voltage: 220-240V~
• Frequency: 50-60Hz
• Power: 1000/2000W
• IP Rating: IP24
• Waterproof: Included
• Remote Control: Included

Introduction

To get the most out of your new Glass Convection Heater with
Wi-Fi, please read through these instructions and the attached
safety regulations before use. Please also save the instruction
manual in case you need to remind yourself of the heater’s
functions at a later date.

Product Usage Instructions

Important Safety Precautions

Before plugging the unit into the mains, ensure by visual
inspection that the unit is intact and has not suffered any damage
during transit.

The appliance must always be placed on a flat and stable
surface. In order to avoid a hazard due to inadvertent resetting of
the thermal cutout, this appliance must not be supplied through an
external switching device, such as a timer, or connected to a
circuit that is regularly switched on and off by the utility.

For Your Own Safety

1. Read all instructions before using the heater.

2. Only connect the heater to a single-phase socket with a mains
   voltage as specified on the rating plate.

3. Do not leave your home while the appliance is in function to
   prevent any potential accidents or damage to the heater.

4. If the heater has been dropped or damaged, it should not be
   used until it has been inspected by a qualified service
   center.

5. Close supervision is necessary when the heater is being used
   around children or vulnerable individuals.

Children’s Safety

Ensure children are supervised to ensure that they do not play
with the appliance. The appliance can be used by children aged 8
years and above and persons with reduced physical, sensory, or
mental capabilities or lack of experience or knowledge if they have
been given supervision or instruction concerning the safe use of
the appliance and understand the hazards involved.

Children of less than 3 years should be kept away from the
appliance unless continuously supervised. Children aged from 3
years to less than 8 years should only switch on/off the appliance
if it has been placed or installed in its intended normal operating
position and they have been given supervision or instruction
concerning the safe use of the appliance and understand the hazards
involved. Cleaning and user maintenance should not be performed by
children without supervision.

Additional Safety Precautions

• Do not leave the heater switched on when leaving your home or
  going to sleep.

• Do not leave unattended when plugged into the mains
  supply.

• Some parts of this product can become very hot and cause burns.
  Particular attention must be given where children and vulnerable
  people are present.

Description of Symbols

In accordance with European directives applicable to this
product:

• WARNING: To avoid overheating, do not
  cover.

• CAUTION: Parts of this unit may become
  hot.

Frequently Asked Questions (FAQ)

1. Q: Is this heater suitable for well-insulated spaces?

A: Yes, this product is only suitable for well-insulated spaces
or occasional use.

2. Q: What is the power rating of this heater?

A: The power rating is 1000/2000W.

3. Q: Is a remote control included with the heater?

A: Yes, a remote control is included.

GLASS CONVECTION HEATER WITH Wi-Fi
INSTRUCTION MANUAL Model No.: R-031
This product is only suitable for well insulated spaces or occasional use.
1

Introduction

To get the most out of your new heater, please read through these instructionsand the attached safety regulations before use. Please also save theinstruction manual in case you need to remind yourself of the heater’sfunctions at a later date.

Technical Specification

Details Voltage Frequency Power IP Waterproof Remote control

R-031 220-240V~ 50-60Hz 1000/2000W IP24 Included

Important
Before plugging the unit into the mains, ensure by visual inspection that theunit is intact and has not suffered any damage during transit.

Caution The appliance must be always placed on a flat and stable surface. Inorder to avoid a hazard due to inadvertent resetting of the thermal cutout,this appliance must not be supplied through an
2

external switching device, such as a timer, or connected to a circuit that isregularly switched on and off by the utility.
For your own safety
1. Read all instruction before using the heater. 2. Only connect the heaterto a single-phase socket with a mains
voltage as specified on the rating plate. 3. Do not leave your home while theappliance is in function:
ensure that the switch is in OFF (0) position and the thermostat is in minimumposition. Always unplug the appliance. 4. Keep combustible material such asfurniture, cushions, bedding, paper, clothes, curtains etc. at least 100cmaway from the heater. 5. Do not hand anything on or in front of the heater. 6.Always use the heater in an upright position. 7. Do not place the heateragainst walls, furniture, curtains, etc. 8. Do not use the appliance in roomsless than 4m² area. 9. Always unplug the heater when not in use. Do not pullthe cord to unplug the heater. 10. Keep the air inlet and outlet free fromobjects at least 1m in front and 50cm behind the heater. 11. Do not installthe heater immediately below a socket- outlet. 12. Do not let animals orchildren touch or play with the heater. Pay attention the air outlet gets hotduring operation. 13. Do not cover. If covered, there is the risk ofoverheating. 14. Do not use this heater in the immediate surroundings of abath, a shower or a swimming pool. 15. Do not use the heater in the roomscontaining explosive gas inflammable solvents, varnish or glue. 16. Keep theheater clean. Do not allow any objects to enter any ventilation or exhaustopening as this may cause electric shock,
3

or fire or damage to the heater. 17. If the heater has been dropped or damagedit should not be
used until it has been inspected by a qualified service center. 18. Closesupervision is necessary when the heater is being used
by or near children, persons suffering from any physical impairment or pets.19. Do not use to dry clothes or any fabric. 20. Do not use the heater to dryyour laundry. Never obstruct the intake and outlet grilles (danger ofoverheating). 21. Do not move the appliance while it is functioning in orderto avoid overheating with the additional risk of fire. 22. If any part of theheater or supply cord becomes damaged, it must be replaced by a qualifiedelectrician. In order to avoid a hazard. 23. The heater must not be locatedimmediately below a socketoutlet. 24. Do not use this heater with aprogrammer, timer or any other device that switches the heater onautomatically, since a fire risk exists if the heater is covered or positionedincorrectly. 25. Do not use this heater if is has been dropped. 26. Do not useif there are visible signs of damage to the heater. 27. Use this heater on ahorizontal and stable surface. 28. WARNING: Do not use this heater in smallrooms when they are occupied by persons not capable of leaving the room ontheir own, unless constant supervision is provided. 29. WARNING: To reduce therisk of fire, keep textiles, curtains or any other flammable material aminimum distance of 1m from the air outlet. 30. WARNING: In order to avoidoverheating, do not cover the heater.
4

31. Do not leave the heater switched on when leaving your home or going tosleep.
32. Children should be supervised to ensure that they do not play with theappliance.
33. This appliance can be used by children aged from 8 years and above andpersons with reduced physical, sensory or mental capabilities or lack ofexperience or knowledge if they have been given supervision or instructionconcerning use of the appliance in a safe way and understand the hazardsinvolved.
34. Children shall not play with the appliance. Cleaning and user maintenanceshall not be made by children without supervision.
35. Children of less than 3 years should be kept away unless continuouslysupervised.
36. Children aged from 3 years and less than 8 years shall only switch on/offthe appliance provided that it has been placed or installed in its intendednormal operating position and they have been given supervision or instructionconcerning use of the appliance in a safe way and understand the hazardsinvolved.
37. Children aged from 3 years and less than 8 years shall not plug in,regulate and clean the appliance or perform user maintenance.
38. Do not leave unattended when plug in to the mains supply. 39. CAUTION —Some parts of this product can become very hot
and cause burns. Particular attention must be given where children andvulnerable people are present. 40. The maximum radioelectric power in thefrequency bands in which the radio equipment operates is 18dBm and 2,4GHz.
5

DESCRIPTION OF THE SYMBOLS
In accordance with European directives applicable to this product
WARNING: To avoid overheating, do not cover
CAUTION: Parts of this unit may become hot
and cause burns. Be very vigilant and avoid touching the hot parts.
SPECIFICATION Model: GH-1901-20-W/ R-031 Standard: IEEE 802.11 b/g/n AntennaType: PCB Antenna Frequency WIFI: 2.400~2.4835GHz Maximum Transmitted Power:18dBm Max Dimension: 16±0.35 mm (W)×24±0.35 mm (L) ×2.9±0.15 mm (H). OperationTemperature: minimum value: -20 max value: 85 Power Input: 220-240V AC,50-60Hz
Producer: Zhongshan SEEMAX Electrical Appliance Co., Ltd Address: 4th floor,Building B, No.13, Dongrui Third Road, Xiaolan Town, Zhongshan City, Guangdongprovince. : +86-757-29960488, Fax:+86-757-29960487
6

SIMPLIFIED EU DECLARATION OF CONFORMITY
Hereby, Zhongshan SEEMAX Electrical Appliance Co., Ltd, declares that theradio equipment type of R-031 is in compliance with Directive 2014/53/EU. Thefull text of the EU declaration of conformity is available at the followinginternet address: www.vassilias.gr
Caution Some parts of the heater can become very hot and cause burns. Do nottouch hot surfaces. Particular attention has to be given where children andvulnerable people are present.
Note These heaters are intended for domestic use only. They can be used asboth portable appliance and wall mounting appliance.
ASSEMBLY
Unpack the heater and the accessories. FREE STANDING USE 1. Place the unitupside down and fix the right and left feet
with screw (Image 1).
7

Image 1
2. Place the unit upright and check if the feet is fixed properly before use(Image 2)
Image 2
8

WALL MOUNTED USE Instruction for fixing the heater on wall:
Image 3
– Take out 1# bracket (2pcs)/2# bracket(1pc)/ST4*14(4pcs) screws of theaccessories bag. – Install 1# bracket at the back of the appliance by fixingthe 4 screws (see picture). – Remove the middle one screw at the bottom ofappliance and install 2# bracket here by fixing this one screw.
9

Image 4
– Installing range for 1# bracket:630mm – Use 6# pressing drill to drill out1# bracket mounting holes on the wall, fit the holes with colloidal particleswithin the accessories bag, then fixing screws ST4*36 on the wall. Note: Screwshould appear 3-5mm
Image 5
– Hang the appliance on the wall, mark the 2# bracket installation hole withpencil.
10

– Remove the appliance, use 6# pressing drill to drill out mounting holes onthe wall, fit the holes with colloidal particles. – Hang the appliance on thewall, fixing 2# bracket with screws ST4*36. – Wall-mounted installationfinished.

Tempered Glass
Standing feet

LED display Touch button
Main switch

11

Remote control
Image 6
Please use 1 commercially available CR2025 button battery (battery isincluded). Pull out the battery box by pressing inside the groove of
the battery box on the back of the remote control with your fingernail.Release CR2025 open the battery box
12

OPERATION
Place the heater on a stable and horizontally even ground. Plug in powersupply, press ON/OFF button (at the bottom of right housing) to connect power.Press it again to disconnect power.

On/Standby switch
Power setting/WIFI Window open detection
Timer

LED display
Program setting Mode switch: P1, P2, P3, P4, P5, UP Increase fortimer/temperature
13 Decrease for timer/temperature

Symbol

Meaning Working at Full power 2000W

Working at 1000W

Anti-frost function

d1,d2,d3,d4,d5,d6,d7 P1,P2,P3,P4,P5

Window open detection function WiFi connection Mon. Tue. Wed. Thur. Fri. Sat.Sun. Factory default program

UP

Customized program setting

Touch once to switch on the appliance. Touch again to switch it off.

1. Set Current Day and Time:

When appliance is switch on, long touch

for 3 seconds to

activate current day setting.

1. Screen will display d1 and it flashes, then touch

to set

Day of the week among d1, d2, d3, d4, d5, d6, d7 in cycle.

Touch

once to confirm the current day setting.

2. Then appliance enter time setting. Hour icon flashes, touch to set currenthour among 00-23 in cycle. Touch
   once to confirm hour. 3) Then follow the same way to set minute among 00-59.Finally

14

Touch once to confirm setting.
After setting finish, touch once in standby mode to check if the current dayand time setting is correct. Screen will automatically show “Day” ­ “Hour” ­“Minutes” in turns within1 second each, then switch back to temperaturedisplay.
For exampe, when your current day setting is Wed. 12:45 a.m., screen will showd3, 12, 45 in turns accordingly.
Note: At the first usage, icon will keep flashing to remind user to setcurrent day and time. It will not stop flashing until current day and time isset. Please finish the setting before any other operation.

2. Power Setting

When appliance is switch on, screen display and appliance

work at full power 2000W. You may touch

button to switch

between 2000W and 1000W.

3. Temperature Setting

After power setting, touch

to activate temperature setting

and choose among 5-40. It will save automatically in 5 seconds

when no further operation is conducted.

Note:

1. When room temperature is found to reach the set temperature,
   appliance will stop heating. When room temperature is found to drop 1 belowset temperature, appliance will recover heating. 2) In anti-frost workingmode, temperature setting is not allowed.

15

4. Mode Switch
When appliance is switch on, touch to select program mode among PI, P2, P3,P4, P5, UP in cycle. – P1, P2, P3, P4, P5 are factory default program andcannot be changed – UP is customized program for end-user to set workingperiod and mode upon their habit.

Table below shows factory default program P1, P2, P3, P4, P5

One Week

mode

Anti-frost

Comfort

Working mode Anti-frost comfort Anti-frost

comfort

Anti-frost

Remark

All day comfort,

1-7

P1

00:00-2 4:00

applicable for everyday use

continuously

1-5

00:00-06:3 06:30-0 08:30-17:0 17:00-2 22:30-24:0

8:30

2:30

Applicable for family who work

6-7

P2

00:00-07:3 07:30-1 10:00-12:0 12:00-1 14:00-17:0 17:00-2 22:30-24:0

0:00

4:00

2:30

in weekdays and be off at
weekends

1-5

00:00-06:0 06:00-1 17:00-24:0

7:00

Applicable in office where is

6-7

P3

00:00-24:0

occupied in week days and
empty in

weekends

Applicable for

1-7

P4

00:00-06:0 06:00-2 22:00-24:0

2:00

commercial place where is occupied all the

way

All anti-frost,

1-7

P5

00:00-24 00

applicable for family who go out for a long

time

• *Anti-frost: appliance keep room temperature at default 5 to

prevent frost.

• *Comfort: upon your need to set power and temperature. (follow

step 2&3)

16

5. Timer Setting

In P1 working mode, touch twice quickly to activate timer

setting. Icon flashes on the screen, then touch

to set

timer reverse among 0 to 24 hours. It will save automatically in 5

seconds after setting. Icon stop flashing and appliance starts count down toturn off.

Touch twice quickly again to cancel timer reverse setting, icon

become gray.

Note: Touh

, switch to other mode, timer reverse will not work,

icon become gray

6. Customized program, UP Setting When appliance is switch on,

1. Touch

button and choose UP mode, then touch

button to activate customized setting to set one (or up to three)

working period in comfort mode.

2. Screen displays d1 to begin Monday setting, touch

once to activate the 1st working period setting, screen display 1

and icon flashes. Touch

once again to select start

time among 0 to 23. Then touch

button to confirm setting,

screen will switch to finish time setting, touch

to

choose and touch

button to confirm. Appliance will

automatically enter into the 2nd working period setting, the

screen will display 2 and icon

flashes. In the same way,

you may set the 2nd and the 3rd working period.

Note:

– Touch

button at first instead of

to keep the appliance in Anti-frost function.

17

can skip the steps

– In comfort mode working time, you may touch

to switch

power setting among

(2000W) and

(100W).

– In spite of the set period, appliance will display room temperature at anti-frost mode at 5.

and keep the

3. Touch

button to confirm every setting, when d1 setting is

finish, it will automatically turn to d2. In the same way, you may

set d2, d3, d4, d5, d6 and d7.

4. When all setting is confirmed, icon stop flashing. 5) Long touch PROGbutton for 3 seconds to check UP mode
   setting,

– touch

button each time to check each setting in turns,

for example, d1 ­ 1st working start time ­ 1st working finish time

and so on.

– touch

button to choose among d1 to d7. Press

to

activate the corresponding day’s working peroid setting.

– it will quit automatically when no operation within 2 minutes.

7. Child Lock Function

When appliance is switch on, long touch

at the same time

for 3 seconds to activate child lock function, screen will show [ ]

after setting and will recover to original display in 5 seconds. No

button will be active during it. Once button is touch, screen will

flashes [ ] and recover to original display in 5 seconds.

Long press

at the same time for 3 seconds again to cancel

child lock function

8. Window Open Detection Function:

When appliance is switch on, touch

once to activate window

open detectionicon flashes on the screen, touch

again

18

to cancel the setting, icon

disappear.

In window open detection mode, when appliance is heating, but room temperatureis found to drop 5°C in 10 minutes, appliance will consider the window mayopen and start detection. In the next 30 minutes, if room temperature hasn’traised, appliance will consider
the window is open and stop heating. At the same time, icon stop flashing andkeep lighting to remind user to close the window.

After closing the window, touch icon flashes again.

to recover orginal operation ,

9.WIFI When appliance is switch on and WIFI module is detected, long

press

3s to activate network connection, the indicator

lights up and flashes to prompt network connection. After the

network connection is successful, indicator lights up and stays

on. In the network connection state, long press 3s to turn off WIFI function,and indicator light will resume flashing.

Note: – After the network connection is successful, the appliance powers onagain after power failure, WIFI function will not turn on(users can notcontrol the appliance by app). In power-on state, touch

twice continuously to turn on WIFI function,

indicator

lights up and stays on. (then users can control the appliance by

app).

10.Reset Quickly touch

and

twice to reset the appliance.

19

MAINTENANCE

WARNING: ALWAYS UNPLUG THE CORD BEFORE MOVING OR

SERVICING

CLEANING: IMPORTANT! DO NOT IMMERSE HEATER IN WATER! DO

NOT TRY TO DISASSEMBLY THE HEATER. DO NOT REMOVE GRILL.

CAUTION: Do not use gasoline, benzene, thinner, harsh cleaners, etc.

as they will damage the Heater. NEVER use ALCOHOL OR SOLVENTS.

STORAGE: Store the heater with these instructions in the original carton in a

cool, dry place

WARNING The Main Power Switch and the On/Off switch should not

:

be used as the sole means of disconnecting power. Always

unplug the power cord before servicing or moving the unit.

To avoid danger of electric shock, unplug from outlet when not in use andbefore cleaning. If the supply cord is damaged, it must be replaced by themanufactory or its service agent or a similarity qualified person in order toavoid a hazard.

DETAILS FOR Wi-Fi CONNECTIVITY
Please scan QR code to download Rohnson APP for Android as below. APP Storefor IOS mobile device

20

Connection by WIFI
1.Use your phone to scan the QR code above or search “Rohnson” App in Playstore or App store. Download and install the Rohnson App.
2.Select Register. Then, select your country, enter email and tap “Continue”to get a message containing verification on code. 3.Enter the verification oncode in the message and tap”Login” to login the App.
4. Please activate the Bluetooth function on your mobile phone.
5. Press the safety switch at the side of the unit, then press the on/offswitch to switch on the product and make sure the product is in WIFI coveredenvironment. The Wi-Fi indicator light will rapidly blinks. If the indicatorlight do not rapidly blinks, please press

”

” button for 5 seconds and the Wi-Fi signal will rapidly

blinks, then go to the App, tap “add device” at the bottom.

21

22

The product will be added successfully In case you see this message, pleasecheck the three possible reasons and retry
23

Now, the unit is off. Press the on/off switch to turn the unit on. Then, theunit is on. You can adjust your desired temperature from 5-40°C.
24

Select Mode to set your desired heating mode. P1, P2, P3, P4, P5 are factorydefault program and cannot be changed. – UP is customized program to setworking period and mode upon your needs. If you want to change the UP program,you have to do it manually on the device.
25

1000W 2000W
Select Gear to choose between 1000W and 2000W.
26

You can select the desired timer to turn the unit off (1-24h)
27

Select Settings to turn on/off the child lock and window open detectionfunction.
28

Select this button for more options on your device. You can change yourproduct’s name, check device info or share your device with other people.Choose device sharing, add sharing, share with the Account Rohnson or otheroptions. You can share the product with maximum 20 people.
29

30

IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITHEC DIRECTIVE 2002/96/EC.
At the end of its working life, the product must not be disposed of as urbanwaste. It must be taken to a special local authority differentiated wastecollection center or to a dealer providing this service. Disposing of ahousehold appliance separately avoids possible negative consequences for theenvironment and health, deriving form inappropriate disposal and enables theconstituent materials to be recovered to obtain significant savings in energyand resources. As a reminder of the need to dispose of household appliancesseparately, the product is marked with a crossed-out wheeled dustbin.
31

Information requirements for electric local space heaters

Model number: R-031

Item

Symbol Value Unit

Heat Output

Nominal P nom

2,0

kW

heat

output

Minimu P min

1,0

kW

m heat

output

(indicati

ve)

Maximu P max.c 2,0

KW

m

continuo

us

heat

output

Auxiliary electricity consumption

At

el max

kW

nominal

heat

output

At

el min

kW

minimu

m heat

output

In standby mode

el SB

0.000 kW 2

Item Symbol Value Unit Type of heat input, for electric storage local spaceheaters only (select one) Manual heat charge No control, with integratedthermostat Manual heat charge No control with room and/or outdoor temperaturefeedback
Electronic heater charge No control with room and/or outdoor temperaturefeedback

Fan assisted heat output No Type of heat output / room temperature control(select one)

single stage heat output No and no room temperature control

Two or more manual

No

stages, no room

temperature control

with mechanic thermostat No

room temperature control

with electronic room

No

temperature control

electronic room

No.

temperature control plus

32

day timer

electronic room

Yes

temperature control plus

week timer

Other control options (multiple

selections possible)

room temperature control, No

with

presence detection

room temperature control, Yes

with open window

detection

with distance control Yes

option

with adaptive start control No

with working time Yes

limitation

with black bulb sensor

No

33

References

• Αρχική - VASSILIAS S.A.
• Αρχική - VASSILIAS S.A.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual>>